TOZEN: RUBBER FLEXIBLE AND EXPANSION JOINT, DI SURABAYA

" TERIMA KASIH ATAS KUNJUNGAN ANDA " Thank You For Visit AGRO INDUSTRI SURABAYA, Please Call us to our Customer Service to: Telp. 031 3989496, 082129846666 Fax. 031 3980197 Email: industri2034@ gmail.com _ _ _ _ _ _ _ _ _ _ _ _ AGRO INDUSTRI KINI TELAH TERHUBUNG DENGAN IMPORTIR DAN DISTRIBUTOR BESAR DI SURABAYA, SEHINGGA KAMI PASTIKAN HARGA TERBAIK UNTUK KEBUTUHAN ANDA. SILAHKAN KIRIM INQUARY ANDA KE: INDUSTRI2034@ GMAIL.COM ATAU MELALUI FAX KE 0313980197 BERIKUT PENAWARAN DARI KAMI: RUBBER FLEXIBLE AND EXPANSION JOINT Rubber/ elastomer flexible connectors have been specified and used for many years by consulting engineers, mechanical contractors, pressure vessel designers, plant engineers and turn-key construction firms. They are installed to accommodate movement in piping runs, protect piping from expansion and contraction. Rubber/ elastomer flexible connectors provide efficient but economic ways to accommodate pressure loads, relieve movement stress, reduce noise, isolate vibration, compensate for misalignment after plants go on stream, and prolong life of motive equipment. Special built-in features will also eliminate electrolysis, counter expansion and contraction against start up surge forces. Tozen rubber/ elastomer flexible connectors are widely used in piping and pumping application in the following industries: Suction and delivery pumping lines for air-conditioning, ventilation system and chilled water installation. Cooling tower and fan coil unit piping lines. Fire fighting and sanitary system. Pollution control system for sewerage and water treatment. Piping systems in general factories. Power generation plan, marine cooling system, ballast lines, pulp and paper industry, etc. Tozen Group has manufactured elastomer flexible connectors for more than 25 years. Producing rubber/ elastomer connectors is our real core business. Most of Tozen rubber flexible connectors are manufactured with multiple plies of nylon tire cord fabric and natural or synthetic rubber under our special molding rocess. The available sizes range from the smallest ½ " up to 80 " 2000mm) in diameters. Available working pressures are from full vacuum up to as high as 40 bar. Inquiries of customized elastomer connectors for specific applications are welcomed. Flexible Joint Installation Instruction : 1) For the installation of the joints to the pump, refer to the right illustration and install. When the check valve is installed before the joints from the pump, there is a possibility of some trouble occurrence due to accumulation of weariness by water head pressure always received and receipt of direct water hammer occurs when the pump starts and stops. flexible1.gif ( 6934 bytes) 2) Install the joints within allowable movements of elongation, compression, eccentricity, angular movement, etc. flexible2.gif ( 13681 bytes) 3) When the joints are in displacement, note for the joints not to touch the structure and equipment ( especially sharp edges) near the installation. 4) Take measurement and make centering correctly not to add unnecessary outer force ( compression, tension, torsion, etc.) when connecting the joints to the pipes. 5) When welding or cutting the pipes nearby after installation, protect the joints with a cover like our SPARK GUARD from sparks. In case of the possibility of heat transmission, take some countermeasure like taking the joints off from the pipe, etc. flexible3.gif ( 8761 bytes) 6) When installation to the outdoor pipes, make lagging to the joints to prevent the joints body aging. flexible4.gif ( 6925 bytes) Notes of Connection : Flange Type Connection 1) In the rubber flexible joints, the packing face of the joints might be damaged depending on the counter flange shape. Check the shape of the counter flange with the followings. The connection to welding neck flanges ( comparatively high pressure flange) is ideal because inner diametre of rubber body and counter flange is almost same and pressure force to the packing is enough. In case of tongue and groove type flanges, do not use them because they have a fault which the packing is damaged easily due to small contact area with a projection and rubber packing sheet and so the unit area load getting bigger. The connection to socket welding type flanges ( a part of JIS 20K) is ideal as well as the above 1 because the contact area is taken enough. In case of slip on counter flanges, it is required for the part of arrow mark to be smoothed or asbestos packing, etc. are required to be used together because the packing will be damaged even though theinner diametre of pipe end is the same as rubber body and if the edge is not smoothed. Basically the packing is not required. But in case of counter flange slip on welding type, the welded edge will become oblique easily as arrow mark and it is possible that the contact area of rubber body seat becomes small and/ or the seat is damaged by edge of arrow mark. In some case the packing is required to be used together. In case counter flange is connected with refraction shape like " L " shape of pipe end of the ilIustration, damage of the seat is not worried because there are no sharp parts and inner diametre of rubber body is almost same as inner diametre of refraction. However, the bend angle " r " is desirable as small as possible. 2) Fix the installation bolts from the joint body side and tighten the nuts at the counter pipe side. It is more safety for the spring washers to be set to prevent looseness of the bolts. In case of the fully threaded bolt, note of the bolt edge not to protrude extraordinary the joint body side. 3) Tighten up the installation bolts in even in the diagonal order. Refer to the following table of the space after tightening of the bolts for each joint. The abnormal installation like uneven bolts tightening, etc. will be a factor of damage of the joints. Nominal Dia. ( mm) S = Space after tightening of the bolts ( mm) PT-CONNECTOR TWINFLEX TOZENFLEX MAFLEX ELBOFLEX( A-type) LINERFLEX( A-typ e) LINERFLEX( C-type) ELBOFLEX ( B.C-type) 20~ 50 1~ 2 8.5 ......... 65 80 100 8.5 125 150 13 200 2~ 3.5 13 250~ 300 4) When the pump operation after the joint installation, the installation bolts are possible to loosen due to the pump vibration. In this case, tighten the bolts slightly again in even in the diagonal order. 5) Table of the installation Bolts Dimension flexible12.gif ( 5666 bytes) Nominal Dia. ( mm) PT-CONNECTOR/ TWINFLEX/ TOZENFLEX/ MAFLEX/ ELBOFLEX( A-Type) / LINERFLEX( A-Type) JIS 5K JIS 10K JIS 20K JWWA 20 - M12 x 50L M12 x 50L - 25 M10 x 40L M16 x 60L M16 x 60L 32 M12 x 50L M16 x 60L M16 x 65L 40 M12 x 50L M16 x 60L M16 x 65L 50 M12 x 50L M16 x 60L M16 x 65L 65 M12 x 50L M16 x 65L M16 x 65L 80 M16 x 60L M16 x 65L M20 x 80L M16 x 65L 100 M16 x 60L M16 x 65L M20 x 80L M16 x 65L 125 M16 x 60L M20 x 75L M22 x 90L M16 x 70L 150 M16 x 65L M20 x 80L M22 x 90L M16 x 70L 200 M20 x 80L M20 x 80L M22 x 100L M16 x 70L 250 M20 x 80L M22 x 90L M24 x 110L M20 x 80L 300 M20 x 80L M22 x 90L M24 x 110L M22 x 80L ( in case of the counter flange material SS400) SCREW TYPE CONNECTION : ( PT-CONNECTOR Screw Type, TWINFLEX Screw Type and TOZENFLEX Screw Type) 1) Remove the installation bolts and take off Flange-A and Socket from the joint body. flexible13.gif ( 6409 bytes) 2) Set Flange-A to the counter pipe and check the correct direction of Flange-A. flexible14.gif ( 2882 bytes) 3) Check smoothness without damage on the thread part of the counter pipe. 4) Wind a sealing tape ( or other sealing material) the thread part of the counter pipe and tighten up Socket by hand up to certain pitch as much as possible, then set a wrench to the edge of Socket to tighten up well also setting a wrench to the counter pipe. flexible15.gif ( 3735 bytes) 5) Fix the installation bolts from the joint side and tighten up the nuts from the counter pipe side. flexible16.gif ( 3811 bytes) 6) Tighten up the bolts in even in the diagonal order avoiding one side tightening. For the space after tightening of the bolts, refer to the following illustration. 7) For the opposite side, set also the same manner as the above 2) -6) . 8) When the pump operation after the joint installation, the installation bolts are possible to loosen due to the pump vibration. In this case, tighten up the bolts slightly again in even in the diagonal order. TWINFLEX : Twinflex is twin sphere rubber connectors. Twinflex is made of neoprene and available from size 15mm to 300mm. For screwed end connection, available sizes are 15mm to 50mm and designed for 10 bar working pressure. For flanged end connections, working pressure shall be 20 bars for size 32mm to 150mm, and 16 bars for size 200mm to 300mm. FCD ANSI 150 and JIS10K floating flanges are standard connectors to Twinflex. Other materials and drilling standards of floating flanges can be supplied upon request. In general, Twinflex provide higher vibration and movement absorption capability than Tozenflex. TWINFLEX 20 : It is a twin sphere rubber connector made of EPDM. Available sizes are 150mm to 300mm. Working pressure is 20 bar for all sizes. Tie-rod integrated type floating FCD flange is the standard flange, and a set of tie rods are supplied as standard package. Ordinary FCD floating flange is also available. JIS10K and ANSI 150 are our standard flange drillings. Other material and drilling standard of flanges can be supplied upon request. In general, Twiflex 20 has higher pressure resistance and shorter face to face length than Twinflex. TOZENFLEX : Tozenflex is single sphere type rubber connectors, and made of EPDM. Available sizes are from 40mm to 300mm. Maximum working pressure is 16 bar for all sizes. FCD ANSI 150 and JIS 10K floating flanges are standard onnectors to Tozenflex. Other materials and drilling standards of floating flanges can be supplied upon request. Tozenflex is commonly suggested for piping systems in general building and industrial services. PT-LS PT-LS is a spool type rubber flexible connectors ( or rubber expansion join) . Since PT-LS is made by hand-made process, customization is available to fulfill specific/ special requirements of sizes ( up to 2000mm available) , lengths, working pressure ( max: 40 bars for small sizes) , movements, and connections. Flanged ends, beveled ends, insertion end are available for different pipe connection. PT-LS can be produced for above-ground and underground applications. Standard material is neoprene and EPDM is optional. PT-LS is widely used in general piping systems requiring higher pressure resistance and movement absorption capability where other models are not suitable. PT-LS is popularly used in large-sized piping systems of public waterworks and wastewater projects to solve differential settlement problems ( land sinking) . FLEXIDRAIN Flexdrain is a spool type rubber flexible connector for underground drainpipes. Both flanged type and insertion are available. Flexidrain is made of natural rubber and available from 25 mm to 250 mm. The maximum working pressure is 1 bar. SALAM HORMAT RAHMAT HIDAYAT 082129847777 24/ 11/ 2015