Protek 6510 100MHz Dual Channel Analog Oscilloscope

Protek 6510 100MHz Dual Channel Analog Oscilloscope

Features

• Four traces may be simultaneously displayed in ALT-sweep
• Five vertical display modes: CH1, CH2, Dual, Add, Subtract
• Vertical mode triggering for displaying 2 unrelated signals
• Trigger hold-off circuit for synchronizing complex waveforms
• Sweep speeds to 2nS/ Div
• 12kV acceleration voltage for bright displays of low duty cycle signals
• Z axis input
• TV Synchronization for either line or field patterns
• 20MHz bandwidth limit switch for triggering signals in a noisy environment

Product Information

100 MHz 2Ch. Dual Time Base with Alt Mag.

Specifications

Vertical Amplifier (CH 1 and CH 2)

• Sensitivity : 5 mV/Div to 5 V/ Div in 7 calibrated steps, (X5 Mag 1mV/ Div to 1 V/ Div)
• Accuracy : ± 3% (± 5% in X5 Mag)
• Bandwidth (-3dB) : DC to 100MHz
• Rise Time : £ 3.5 ns, X5 Mag: 20MHz Bandwidth: £ 17 ns
• Input Impedance : 1MW + 25 pF
• Input Coupling : AC-Gnd-DC
• Invert Channel : CH2
• Display Modes : CH1, CH2, Add, Subtract, Dual (Alt/Chop)
• Maximum Input Voltage : 400V (DC or AC peak)
• CH1 Signal Output : 20mV into 50W

Horizontal Sweep

• Timebase A – Sweep Time : 50ns/Div to 0.2 s/Div in 21 calibrated steps (1-2-5)
• Timebase A – X10 Mag : 5ns/Div to 20ms/ Div
• Timebase A – Accuracy : ± 3% (± 5% in X10 Mag)
• Timebase A – Hold Off : Continuously adjustable to > 2X sweep time
• Timebase B – Sweep Time : 50ns/Div to 10µ s/ Div in 8 steps (1-2-5)
• Timebase B – Accuracy : ± 3%
• Timebase B – Delay Time : Continuously variable from 0.2µ s to 2s
• Timebase B – Delay Modes : Continuous or triggered
• Timebase B – Sweep Displays : A, B, A alt B, B triggered, X-Y

X-Y Mode

• CH1-X axis, CH2-Y axis Sensitivity : Same as CH1 vertical amplifier
• Bandwidth (X-axis) : DC to 2MHz
• Phase Error : £ 3° DC to 10kHz

Triggering

• Trigger Modes : Auto, Normal, TV-V, TV-L
• Source : Int. CH2, line ext.
• Coupling : AC
• Slope : Positive or negative
• Trigger Sensitivity :
  • Int (DC to 10MHz) : 0.5 Div
  • Int (10MHz to 100MHz) : 1.5 Div
  • Ext (DC to 10MHz) : 200mV
  • Ext (10MHz to 100MHz) : 500mV
  • TV (Int) : 1 Div Min
  • TV (Ext) : 1V P-P
  • External Trigger Input : Impedance: 1MW + 20 pF
  • Maximum Input Volts : 400V DC or AC peak

Z Axis Modulation

• Sensitivity : ± 5V P-P Intensity increases with a negative going voltage input
• Bandwidth (-3dB) : DC to 2MHz
• Input Impedance : Approx. 2 KW

Calibrator Signal

• Voltage                : 0.5V ± 3% P-P 1kHz Square Wave
• Duty Cycle : Approx. 50%

CRT

• Type : 6″ rectangular CRT with internal graticule. (1 Div = 1cm)
• Acceleration Voltage : 12 kV

General Specification

• Power Requirements : AC Input Voltage: 100V, 120V, 220V, 240V selectable
• Frequency : 50/60Hz
• Power Consumption : 55W
• Operating Temperature : 0 to 40° C at 35% to 85% relative humidity
• Dimensions : 5.25″ H × 12.67″ W × 14.5″ D
• Weight : 24 lbs.
• Supplied Accessories : Manual, 1 AC Power cord, (2) X10 Probes.